收藏本站
CHAPTER 6 PG-FP4 OPERATION IN STANDALONE MODE
6.1.2
[Type Setting] menu
The [Type Setting] menu is used to check the target device rewrite environment currently set for the PG-FP4. All
the values displayed were set during the last programming session.
The setting cannot be changed by this menu.
[Type Setting >]
? Pressing the Next key displays the [Option Setting] menu.
? Pressing the Enter key displays the following commands that can be executed from the [Type Setting] menu.
? Pressing the Cancel key displays the [Commands] menu again.
[ Device Port ]
Device Port displays any of the following to indicate what is selected as an interface between
the target device and the PG-FP4.
SIO 0, SIO1, SIO 2, SIO H/S, IIC 0, IIC 1, IIC 2, IIC 3,
UART 0, UART 1, UART 2, UART 3, PORT 0, PORT 1, PORT 2
↓ Next button
[ Multiply Rate ]
↓ Next button
[ Serial CLK ]
Multiply Rate displays the multiplication rate of the operating clock of the target device.
Serial CLK displays the serial clock rate in Hz that is used to interface the target device and
PG-FP4.
↓ Next button
[ CLK source ]
CLK source indicates either of the following as a source to supply the operation clock to the
target device.
Programmer: Clock is supplied from the PG-FP4.
↓ Next button
Target:
Clock is supplied on the user system.
[ PG CPU CLK ]
PG CPU CLK indicates the frequency of the clock supplied by the PG-FP4 in MHz.
↓ Next button
[ Target CPU CLK ] Target CPU CLK indicates the frequency of the clock on the user system that is supplied to
the target device, in MHz.
↓ Next button
[ Mode ]
Mode indicates any of the following operation modes when the Blank Check, Erase,
Program, Verify, or EPV command is executed.
chip, area, block
Display example
Mode
BEPV: chip
↓ Next button
82
[ PRG Area ]
PRG Area indicates which of the areas of the target device connected to the PG-FP4 is to be
programmed. This menu is valid only when the operation mode is other than chip (only when
area or block is displayed in the above mode).
Display example
PRG Area
0 to 1
*In the chip mode, the display is always as follows:
PRG Area
0 to 0
User ’s Manual U15260EJ4V0UM
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
PG15S-D20-HHB9 MOTOR GEARED STEPPER 15MM 15V BI
PG164120 PROGRAMMER MCU PICKIT 2
PG20L-D20-HHC0 MOTOR GEARED STEPPER 20MM 10V BI
PG25L-D24-HHC1 MOTOR GEARED STEPPER 25MM 24V BI
PG35S-D48-HHC2 MOTOR GEARED STEPPER 35MM 24V BI
PIC12F683 DEVELOPMENT KIT KIT DEV EMBEDDED C
PIC18F4520 DEVELOPMENT KIT KIT DEV EMBEDDED C
PIC18F67J10 DEVELOPMENT KIT KIT DEV EMBEDDED C
相关代理商/技术参数
PG-FP5 制造商:Renesas Electronics Corporation 功能描述:MCU,Programmer,NEC Flash MCU
PG-FP5-AS 制造商:Renesas Electronics Corporation 功能描述:MICROCOMPUTER FLASH MEMORY PROGRAMMER 制造商:Renesas Electronics Corporation 功能描述:PROGRAMMER FLASH RL78 V850 7
PG-FP5-EA 功能描述:PROGRAMMER FLASH MEMORY UNIV RoHS:是 类别:编程器，开发系统 >> 内电路编程器、仿真器以及调试器 系列:* 产品变化通告:Development Systems Discontinuation 19/Jul/2010 标准包装:1 系列:* 类型:* 适用于相关产品:* 所含物品:*
PGFP-A11 功能描述:PLUG GFCI 120VAC 15/20A AUTORST RoHS:是 类别:过电压，电流，温度装置 >> 接地故障电路断路器 (GFCI) 系列:PGFP 标准包装:1 系列:PGFI 类型:带 6 英尺引线的直列接头 技术规格:120V 其它名称:723-1041
PGFP-A110KYST2 功能描述:CORD GFCI 120VAC 2' YEL SNG TAP RoHS:是 类别:过电压，电流，温度装置 >> 接地故障电路断路器 (GFCI) 系列:PGFP 标准包装:1 系列:PGFI 类型:带 6 英尺引线的直列接头 技术规格:120V 其它名称:723-1041
PGFP-A110KY-ST2 制造商:Airpax 功能描述:
PGFP-A110KYST25 功能描述:CORD GFCI 120VAC 25' YEL SNG RoHS:是 类别:过电压，电流，温度装置 >> 接地故障电路断路器 (GFCI) 系列:PGFP 标准包装:1 系列:PGFI 类型:带 6 英尺引线的直列接头 技术规格:120V 其它名称:723-1041
PGFP-A110KYTT2 功能描述:CORD GFCI 120VAC 2' YEL TRITAP RoHS:是 类别:过电压，电流，温度装置 >> 接地故障电路断路器 (GFCI) 系列:PGFP 标准包装:1 系列:PGFI 类型:带 6 英尺引线的直列接头 技术规格:120V 其它名称:723-1041